What error are you experiencing? *

For any problems related to airtightness, please try these steps.

1. Ensure that you are using the product in on-mode, and that you have closed the lid firmly.

The product is generally more airtight the harder the lid is closed, but don't close it so tightly that it's difficult to open again.

2. Check that the threads of the lid and cylinder are clean and that no dirt is stuck.

3. Take out and adjust the loose rubber O-ring on the inside of the lid, using this quick guide.

4. If none of the above works, use this quick guide to adjust the top part.

Did these steps help? *

Understood, these troubleshooting steps typically works for leaks.

Lets try something else to identify the source of the leak.

1. Remove the silicone cover by loosening it around the USB-port and slowly drag it off.

2. Pressurize the container with the lid firmly closed, and place the small lid underwater without exposing any electronics.

3. If there are bubbles coming out from the lid - please check where the bubbles comes from, and try adjusting the seal again by adjusting the o-ring once more using this guide.

4. If there are no bubbles, the leak is from the large top lid of the container. Then please try once more to adjust the top part using this guide.

5. If the problem can not be solved, please film the underwater test for us and click next. You will be asked to upload the video in the next step.

For any problems related to electronics, try these steps:

1. Leave the device off overnight.

2. Recharge the device until all four lights stop flashing. This will reset the device.

3. Ensure the device is disconnected from the charging cable before attempting to use it.

4. If the device doesn't start, firmly tap the compressor part of the box with your hand immediately after the click and/or after turning on the product. This should help if the pump is stuck for some reason.

5. Try removing the silicone cover and using the device without it. A misplaced cover could potentially block the air inlet. To remove the silicone cover, loosen it around the USB-C port and then take a firm grip and drag it slowly but steadily up without folding it.

6. Please create a video illustrating the issue with the pump (without the silicone cover). You will be able to upload it in the next step.

Great! We are happy that it helped.

You can close this window now. Please check out our FAQ again if you have any other questions or issues!

Understood! Here are some general troubleshooting steps that may help. Make sure to check all of them and if you can not find a suitable solution, please click "Next".

Having Trouble Opening the Lid?

Answer: For ease of opening, make sure not to close the box too hard.

If you have closed the lid hard and are having trouble opening it, there are a few tricks that you can try.

1. First, make sure that you have deflated the box. If you still can't open it, try using a glove (skin gloves give the best grip), towel, or ask someone strong to help you.

2. If it still does not work, try to gently knock with a spoon around the lid (this reduces friction), and then try to open.

3. Remove the silicone cover for better grip. Just push it up, and it can be removed. For the next time, check the inside of the lid for dirt and follow the steps for airtightness and close the box softer.

4. If you are still having problems to open the box, let us know, and we will help you out.

Having Problems Related to Ball Pressure?

Situation: The balls are too hard.

Solution: Since the pressure inside Pressurebox is higher than the internal pressure in tennis & padel balls, the balls can sometimes get too hard if they are in the box for long. However, this is an easy problem to solve. Just open the box some time before you play, and the balls will get softer, as long as they are not stored under pressure.

Situation: The balls are not hard enough.

Solution: If the balls used are too soft & old initially, it may take some time to restore the pressure. It is advisable to use balls with some pressure from the start and utilize the Pressurebox frequently in between each session to maintain optimal pressure.

Optimizing Airtightness & Battery Life

Please try the steps below if you are experiencing one or more of these problems:

- The product is leaking air

- The compressor restarts often

- The battery life is shorter than expected

1. Ensure that you are using the product in on-mode, and that you have closed the lid firmly.

The product is generally more airtight the harder the lid is closed, but don't close it so tightly that it's difficult to open again.

2. Check that the threads of the lid and cylinder are clean and that no dirt is stuck.

3. Take out and adjust the loose rubber O-ring on the inside of the lid, using this quick guide.

4. If none of the above works, use this quick guide to adjust the top part.

If the problem persists, please reach out and let us know how the performance of the product changed for each of the steps 1-4. This information will be required for us to understand the issue.

Electronics: Troubleshooting & Maintainance

For any problems related to electronics, try these steps:

1. Leave the device off overnight.

2. Recharge the device until all four lights stop flashing. This will reset the device.

3. Ensure the device is disconnected from the charging cable before attempting to use it.

6. Contact us with a video illustrating the issue with the product without the silicone cover, including the numbers on the lid & attach your receipt/order confirmation.

Name *

Current Address *

Country *

Email *

Phone *

Where Did You Order From? *

Order number *

Product *

Please Explain Issues With Product *

What troubleshooting steps have you tried? *

Order Confirmation or Receipt *

Choose file or drag here

Supported format: PDF, JPG, JPEG, PNG, DOC

temp-for-95153-file2-1_

Video of Error

Choose file or drag here

Please make sure the video proves the defect. Supported format: Mp4, Mov. Max Size: 30 MB.

temp-for-95153-file2-2_

Image of the number of the lid for verifcation *

Choose file or drag here

Supported format: JPG, JPEG, PDF, PNG,

temp-for-95153-file2-3_

Number on the lid of the product in writing *

Order Date *

Tak for din henvendelse!

Din reklamation er nu indsendt.

Vi gennemgår de oplysninger, du har sendt, og vender tilbage til dig inden for de næste par dage. Du behøver ikke indsende formularen igen.

For en ekstra sikkerhed er du meget velkommen til også at sende os en mail, når formularen er udfyldt – så er vi sikre på ikke at overse din henvendelse.

Tak for din tålmodighed – vi vender tilbage hurtigst muligt.

Tak for din henvendelse!

Din reklamation er nu indsendt.

Vi gennemgår de oplysninger, du har sendt, og vender tilbage til dig inden for de næste par dage. Du behøver ikke indsende formularen igen.

For en ekstra sikkerhed er du meget velkommen til også at sende os en mail, når formularen er udfyldt – så er vi sikre på ikke at overse din henvendelse.

Tak for din tålmodighed – vi vender tilbage hurtigst muligt.

Troubleshooting & Warranty Requests

Pressurebox Core Pump